http://www.shoulder.cn shoulder electronics co., ltd. shoulder electronics co., ltd. ceramic resonator data sheet product ? : ceramic resonator model no : z tacv....mt prepared : fengyu checked : york approved ? : date : 2007-01-25
1. scope the specification is fit for ceramic resonator 8.00 - 13.00mhz. 2. part no: ztacv ? mt 3. e lectrical characteristics no. item characteristics 3 - 1 oscillate frequency (mhz) 8.00 - 13.00 3.2 frequency tolerance max 0.5% 3.3 resonant impedance max ( w ) 30 3.4 built ? in capacitance (pf) -- 3.5 insulate resistance min (m w ) 100 3.6 withstanding voltage d.c (v) 100 max 5 sec 3.7 voltage 1 d.c voltage max v 2 input voltage max v 6 15vp - p 3.8 temp characteristics of oscillate frequency max 0.3% 3.9 operating temp range - 20 ~ +80 3.10 storage temp ( ) - 55 ~ +85 4. test circuit 5v output ic ic 1mohm x c1 c2 ic: 1/6tc4069ubpx2 x: ceramic resonator c1c2: 30pf
5. dimension 6. physical and environmental characteristics no item condition of test performance requirements 6.1 humidity keep the resonator at 40 2 and 90 - 95% rh for 96 4 hours. then release the resonator into the room condition for 1 hour prior to the measurement. it shall fulfill the specifications in table 1. 6.2 vibration subject the resonator to vibration for 2 hours each in x,y and z axis w ith the amplitude of 1.5mm, the frequency shall be varied uniformly between the limits of 10 - 55hz it shall fulfill the specifications in table 1. 6.3 mechanical shock drop the resonator randomly onto a concrete floor from the height of 100 cm 3 times. i t shall fulfill the specifications in table 1.
passed through the re - flow oven under the following condition and left at room temperature for 1 hour before measurement. temperature at s urface of the substrate time preheat 150 5 60 10 sec. 6.4 soldering test peak 240 5 10 3 sec. it shall fulfill the specifications in table 1. 6.5 solder ability dip the resonator terminals into the solder bath at 230 5 for 3 0.5 sec. more than 95% of the terminal surface shall be covered. 6.6 high temper ature exposure subject the resonator to 80 5 for 96 4 hours. then release the resonator into the room conditions for 1 hour prior to the measurement. it shall fulfill the specifications in table 1. 6.7 low temperature subject the resonator to ? 20 5 for 96 4 hours. then release the resonator into the room conditions for 1 hour prior to the measurement. it shall fulfill the specifications in table 1. 6.8 temperature cycling subject the resonator to ? 20 for 30 minutes followed by a high temperature of 85 for 30 min. cycling shall be repeated 5 times with a transfer time of 15 second at the room condition for 1 hour prior to the measurement. it shall fulfill the specifications in table 1. table1 item specification oscillation frequency change f/fo 0.3% max resonant impedance ro 10 ohm 7.
8. packing tape dimension (mm) a 0.2 b 0.2 c 0.3 d 0.1 e 0.1 f 0.1 g 0.1 h 0.1 ?j 0.1 ?n 0.1 m max r max k 0.2 t 0.1 mg 3.8 7.8 16.0 7.5 2.1 mt 5.0 4.4 12.0 5.5 1.8 mx 3.4 4.0 12.0 5.5 1.75 8.0 4.0 2.0 1.5 1.6 10 0.3 1.3 0.3 standard package: 1kpcs / reel
|
